A Comparison of Two Implant Systems in Restoration of Hip Geometry in Arthroplasty.
Summary of "A Comparison of Two Implant Systems in Restoration of Hip Geometry in Arthroplasty."
Restoration of hip offset and leg length during THA is often limited by available implant geometries. The recent introduction of femoral components with a modular junction at the base of the neck (two modular junction components) has expanded the options to restore femoral offset and leg length. QUESTIONS/
We asked (1) whether a femoral component with two modular junctions would predict by templating more frequent restoration of preoperative offset and leg length abnormalities than one with single modular junctions; and (2) how our use of these options compared with national sales data. PATIENTS AND
We retrospectively reviewed the preoperative templating data in 100 primary THAs using single modular junction implants with only a neutral version stem and 100 THAs using two modular junction implants. We compared the frequency with which the desired leg length and offset were completely restored by preoperative templating in the two groups.
Offset and leg lengths were restored to within 1 mm in 85% of cases with two modular junction implants and 60% of cases with single modular junction implants. An anteverted or a retroverted neck was used in 25% of cases with the two modular junction stems. The national sales data revealed femoral neck components with version were used in 28% of cases.
The use of a femoral component with two modular junctions resulted in more frequent ability to restore femoral offset and leg length than a single modular junction. The advantage of clinical flexibility should be tempered by the potential concerns of prosthetic mechanical failure (which has been reported in another implant system with two modular junctions), increased third-body wear and corrosive debris, and increased prosthetic cost. LEVEL OF
Level II, prognostic study. See Guidelines for Authors for a complete description of levels of evidence.
The New Mexico Center for Joint Replacement Surgery, New Mexico Orthopaedics, 201 Cedar SE, Suite 6600, Albuquerque, NM, 87106, USA, firstname.lastname@example.org.
This article was published in the following journal.
Name: Clinical orthopaedics and related research
- PubMed Source: http://www.ncbi.nlm.nih.gov/pubmed/21082363
- DOI: http://dx.doi.org/10.1007/s11999-010-1678-9
No longer merely a concept for the future, the use of digital technologies in dentistry has become common practice today. Computed tomography (CT)-guided dental implant surgery has greatly expanded ov...
Dental implantology is the state of the art technique to replace missing teeth. Implant stability of implant jeopardizes its longevity and success of treatment. This study evaluates the implant stabil...
The aim of this study is to compare two commercially available screw-type sandblasted and acid-etched (SLA) Ti implant systems from Eckermann Laboratorium S.L., with similar geometry and distinct micr...
Studies have shown that bone quality at the implant recipient site can influence primary stability.
Flapless Postextraction Socket Implant Placement in the Esthetic Zone: Part 1. The Effect of Bone Grafting and/or Provisional Restoration on Facial-Palatal Ridge Dimensional Change-A Retrospective Cohort Study.
The dental literature has reported vertical soft tissue changes that can occur with immediate implant placement, bone grafting, and provisional restoration ranging from a gain or loss of 1.0 mm. Howev...
The purpose of this study is to prospectively evaluate two FDA approved implant designs for the Tornier Reverse Shoulder arthroplasty. The small difference in design is the amount of offse...
The purpose of this study is to determine whether patient rehabilitation is equal for patients operated with two different knee implant designs. The patients are randomized to treatment w...
The purpose of the study is to investigate fixation to bone and the clinical results following shoulder resurfacing arthroplasty. The study will compare results between an implant made of ...
The purpose of this study is to demonstrate survivorship of the femoral stem at 5 years.
This study compares two different hip stem components. Both hip stems used in this study allow the femur bone to attach and grow into them for stability. The main difference between the t...
Medical and Biotech [MESH] Definitions
Comparison of various psychological, sociological, or cultural factors in order to assess the similarities or diversities occurring in two or more different cultures or societies.
A prosthesis or restoration placed for a limited period, from several days to several months, which is designed to seal the tooth and maintain its position until a permanent restoration (DENTAL RESTORATION, PERMANENT) will replace it. (From Jablonski, Dictionary of Dentistry, 1992)
Insertion of an implant into the bone of the mandible or maxilla. The implant has an exposed head which protrudes through the mucosa and is a prosthodontic abutment.
Endosseous dental implantation where implants are fitted with an abutment or where an implant with a transmucosal coronal portion is used immediately (within 1 week) after the initial extraction. Conventionally, the implantation is performed in two stages with more than two months in between the stages.
The process of repairing broken or worn parts of a PERMANENT DENTAL RESTORATION.