Advertisement

Topics

Surface Topography, Gloss and Flexural Strength of Pressable Ceramic After Finishing-Polishing Protocols.

07:03 LMT 1st January 0000 | BioPortfolio

Summary of "Surface Topography, Gloss and Flexural Strength of Pressable Ceramic After Finishing-Polishing Protocols."

This study evaluated the effect of different finishing-polishing protocols on surface roughness, gloss, morphology and biaxial flexural strength of pressable fluorapatite glass ceramic. Thirty ceramic discs (12x1 mm) were produced and divided into five groups (n=6):
CT:
control (glaze);
DA:
fine grit diamond bur;
DG:
DA + new glaze layer;
DP:
DA + felt disk with fine grit diamond paste;
DK:
DA+ sequential polishing with silicon abrasive instruments, goat hair brush and cotton wheel. The specimens were analyzed for surface roughness (Ra) under profilometry and atomic force microscopy (AFM). Gloss was measured with spectrophotometry and micromorphology with scanning electron microscopy (SEM). Flexural strength was assessed by biaxial flexural strength test. Data were analyzed using one-way ANOVA and Tukey's post hoc test (a=0.05). DK showed the lowest surface roughness values and DA presented the highest in the perfilometer analysis. No significant differences were observed in the AFM for the CT, DG and DK groups, which presented the lower surface roughness; DA and DP had the higher Ra values. The DA, DP and CT showed the lowest surface gloss values, and the reflectance was significantly different from those observed for DK and DG groups. SEM analysis revealed the smoothest surface for DK group, followed by DG and CT groups; DA and DP groups exhibited variable degrees of surface irregularities. No significant differences were observed among groups for the biaxial flexural strength. The polishing protocol used in DK group can be a good alternative for chairside finishing of adjusted pressable fluorapatite glass ceramic surfaces.

Affiliation

Journal Details

This article was published in the following journal.

Name: Brazilian dental journal
ISSN: 1806-4760
Pages: 164-170

Links

DeepDyve research library

PubMed Articles [8415 Associated PubMed Articles listed on BioPortfolio]

Effect of carbamide peroxide bleaching agent on the surface roughness and gloss of a pressable ceramic.

This study evaluated the influence of carbamide peroxide, 10% and 16%, on the surface roughness and gloss of a pressable ceramic.

Short fiber reinforced 3d printed ceramic composite with shear induced alignment.

This paper accounts for utilization of shear induced alignment method during ceramic stereolithography. Lateral oscillation mechanism, combined with 3d printed wall pattern, was employed to generate n...

Polishing of Ground Y-TZP Ceramic is Mandatory for Improving the Mechanical Behavior.

It evaluated the effect of aging by Low Temperature Degradation (LTD), executed after post- processing surface treatments (polishing, heat treatment and glazing), on the surface characteristics (micro...

Strength of a Zirconia-Reinforced Lithium Silicate Ceramic: Acid-Etching Time and Resin Cement Application Effects.

This study aimed to evaluate the effect of hydrofluoric (HF)-acid-etching time and the impact of a resin-cement layer on the biaxial flexural strength and structural reliability of a zirconia-reinforc...

The Use of Different Photoinitiator Systems in Photopolymerizing Resin Cements Through Ceramic Veneers.

To evaluate the effect of different photoinitiator systems on photopolymerizing resin cements through ceramic veneers with different thickness on microshear bond strength (μSBS), flexural strength (F...

Clinical Trials [2835 Associated Clinical Trials listed on BioPortfolio]

One Year Clinical Evaluation of E-max CAD/CAM Versus Cerasmart Endocrowns in Anterior Endodontically Treated Teeth:A Randomized Clinical Trial

Nowadays Endocrowns are classified as conservative treatment modality for restoration of Endodontically treated teeth in which pulp chamber is used as a retentive resource. With the advan...

Evaluation of the Surface Topography for Monitoring Scoliosis Patients Aged 10-13 Years

The main objective of the study is to investigate the correlation between the measurement of the Cobb angle (angle of scoliosis) by conventional radiography and angle measured by surface t...

Measuring Quality of Life of Poly-amide Complete Dentures

Polymethyl methacrylate have been used since 1937 as a gold standard for a denture base material because of its several advantages as; good esthetics, adequate strength, easy repair and si...

Zirconia and Metal-based Single Crown Posterior Restorations.

The objective of this study was to compare the 5-year survival and clinical behavior of single posterior ceramic crowns made with pressable ceramic on zirconia or on a metal framework. If ...

STernectOmy Repair Efficiency of a Ceramic Implant

For the replacement of the sternum, there is no consensus regarding the most appropriate and most effective physiologically material. The use of ceramic implant offers significant operatio...

Medical and Biotech [MESH] Definitions

Asymmetries in the topography and refractive index of the corneal surface that affect visual acuity.

The internal resistance of a material to moving some parts of it parallel to a fixed plane, in contrast to stretching (TENSILE STRENGTH) or compression (COMPRESSIVE STRENGTH). Ionic crystals are brittle because, when subjected to shear, ions of the same charge are brought next to each other, which causes repulsion.

The amount of force generated by MUSCLE CONTRACTION. Muscle strength can be measured during isometric, isotonic, or isokinetic contraction, either manually or using a device such as a MUSCLE STRENGTH DYNAMOMETER.

The systematic surveying, mapping, charting, and description of specific geographical sites, with reference to the physical features that were presumed to influence health and disease. Often associated with Hippocrates, the process became a significant part of public health investigation and epidemiological methodology, particularly between the 17th and 19th centuries. Medical topography should be differentiated from EPIDEMIOLOGY in that the former emphasizes geography whereas the latter emphasizes disease outbreaks. (Dr. James H. Cassedy, NLM History of Medicine Division)

A type of porcelain used in dental restorations, either jacket crowns or inlays, artificial teeth, or metal-ceramic crowns. It is essentially a mixture of particles of feldspar and quartz, the feldspar melting first and providing a glass matrix for the quartz. Dental porcelain is produced by mixing ceramic powder (a mixture of quartz, kaolin, pigments, opacifiers, a suitable flux, and other substances) with distilled water. (From Jablonski's Dictionary of Dentistry, 1992)

Advertisement
Quick Search
Advertisement
Advertisement

 


DeepDyve research library

Searches Linking to this Article