Advertisement

Topics

Low Speed Drilling Versus Conventional Drilling Technique on Crestal Bone Level in Maxilla.(Group A ) A Randomized Controlled Clinical Trial

2017-07-19 10:53:23 | BioPortfolio

Summary

20 patients were selected requiring implant placement and divided randomly into two groups (10 in each group)

- for the study group, starter drill is used to locate the point of insertion as planned then pilot drill is also used to the full desired working length after that all other sequential drills are used at a low speed (50-70 rpm) without irrigation .

- In the study group: implant will be inserted in the low speed osteotomy site. • In the control group: implants will be inserted in the conventional prepared osteotomy site.

- For both groups there is no surgical guide used.

- The flap will then be copiously irrigated with saline in preparation for closure.

- The flap will then be closed using interrupted 4/0 resorbable sutures.

Study Design

Conditions

Bone Resorption

Intervention

Drilling at low speed, Conventional drilling at high speed

Status

Active, not recruiting

Source

Cairo University

Results (where available)

View Results

Links

Published on BioPortfolio: 2017-07-19T10:53:23-0400

Clinical Trials [2075 Associated Clinical Trials listed on BioPortfolio]

Low Speed Drilling Versus Conventional Drilling Technique on Crestal Bone Level in Maxilla.(Group C ) A Randomized Controlled Clinical Trial

20 patients were selected requiring implant placement and divided randomly into two groups (10 in each group) - for the study group, starter drill is used to locate the point of insert...

Clinical Evaluation Of Dental Implants Stability Placed In Healed Bony Sites Following Over-drilling Compared To Conventional-Drilling Protocol

Clinical Evaluation Of Dental Implants Stability Placed In Healed Bony Sites Following Over-drilling Compared To Conventional-Drilling Protocol

Single-blind Evaluation of Device to Nail Micro-drilling in Onychomycosis

Based on manufacturer testing, no major difference in drilling condition is expected in this study compared to the drilling conditions previously established. However clinical testing is ...

LESS Surgery Versus Conventional Multiport Laparoscopy for Polycystic Ovary Syndrome in Infertile Women Undergoing Ovarian Drilling

laparoendoscopic single-site surgery is compared to conventional multi-port laparoscopy for polycystic ovary syndrome in infertile women undergoing ovarian drilling as regards successful s...

The Histological Effect of Various Microfracture Techniques on Human Chondral & Sub-chondral Tissue - an Ex-Vivo Study

The subchondral bone, formed by the subchondral bone plate and the subarticular spongiosa, plays a key role in supporting the articular cartilage. Marrow stimulation techniques such as sub...

PubMed Articles [19982 Associated PubMed Articles listed on BioPortfolio]

A Novel Well Drill Assisted with High-Frequency Vibration Using the Bending Mode.

It is important for companies to increase the efficiency of drilling as well as prolong the lifetime of the drilling tool. Since some previous investigations indicated that a superposition of well dri...

A cadaveric study of bone tissue temperature during pin site drilling utilizing fluoroptic thermography.

Using fluoroptic thermography, temperature was measured during pin site drilling of intact cortical human cadaver bone with a combination of one-step drilling, graduated drilling, and one-step drillin...

Investigation on the Effect of a Pre-Center Drill Hole and Tool Material on Thrust Force, Surface Roughness, and Cylindricity in the Drilling of Al7075.

Drilling is one of the most useful metal cutting processes and is used in various applications, such as aerospace, electronics, and automotive. In traditional drilling methods, the thrust force, torqu...

Theoretical analysis and design of hydro-hammer with a jet actuator: An engineering application to improve the penetration rate of directional well drilling in hard rock formations.

Rapid horizontal directional well drilling in hard or fractured formations requires efficient drilling technology. The penetration rate of conventional hard rock drilling technology in horizontal dire...

A new drilling method-Earthworm-like vibration drilling.

The load transfer difficulty caused by borehole wall friction severely limits the penetration rate and extended-reach limit of complex structural wells. A new friction reduction technology termed "ear...

Medical and Biotech [MESH] Definitions

A drilling technology in which NATURAL GAS is extracted from large deposits of impermeable rock formations known as shale, deep within the earth’s crust. This drilling technique involves injecting large volumes of high-pressure fracturing fluid (a mixture of water, sand, and chemicals) several thousand feet underground, thereby creating cracks or fissures in the shale formation, and releasing trapped gas.

Dental methods involving the use of DENTAL HIGH-SPEED EQUIPMENT.

Liquid chromatographic techniques which feature high inlet pressures, high sensitivity, and high speed.

Tools used in dentistry that operate at high rotation speeds.

Surgical techniques used to correct or augment healing of chondral defects in the joints (CARTILAGE, ARTICULAR). These include abrasion, drilling, and microfracture of the subchondral bone to enhance chondral resurfacing via autografts, allografts, or cell transplantation.

More From BioPortfolio on "Low Speed Drilling Versus Conventional Drilling Technique on Crestal Bone Level in Maxilla.(Group A ) A Randomized Controlled Clinical Trial"

Advertisement
Quick Search
Advertisement
Advertisement

 

Relevant Topic

Osteoporosis
Osteoporosis is a disease in which the bones become extremely porous, are subject to fracture, and heal slowly, occurring especially in women following menopause and often leading to curvature of the spine from vertebral collapse. Follow and track&n...


Searches Linking to this Trial